Inkyfingers Papercrafting

Tutorial: Angled Slide-Lock Card

Posted on: April 22, 2021

The Angled Slide-Lock Card is harder to say than it is to create! I learned this fold from fellow demonstrator Erica Edney, and I hope you have fun making it. Keep in mind that in order to create the locking mechanism, you will need the Classic Label punch, which is retiring and only available while supplies last.

Start with a cardbase measuring 5.5 x 10.5”. Score this piece at just a hair less than 4.25” and at 8.5”. Burnish the folds with your bone folder.

Now, with the smaller flap folded down, mark along the top at at 1” from the right edge.

Line up this mark in your trimmer and cut from the mark diagonally to the bottom corner of the flap.

Now your cardbase looks like this.

Note: The reason to put your first scoreline at just a hair less than 4.25″ is so that the larger flap can easily fold under the smaller one as shown above, without the two flaps bumping into each other and buckling. If you put your scoreline right on 4.25″, the flaps won’t have enough room to fold together.

Cut two pieces of Designer Series Paper:
4 x 5.25”
1.75 x 5.25”

Mark the smaller piece of DSP at 0.75” from the top right …

…and trim diagonally as you did with the cardbase.

Now it’s time for some punching! Use the Classic Label Punch on the large flap of the cardbase. Leaving about ½” on right side, slide the cardstock into punch as far as it will go.


Now close the large flap over the small one, and mark the right edge of the punched label shape with a pencil as shown.

Punch the smaller flap where marked. The smaller flap will only have part of the label shape punched out.
You can now add adhesive to the outside of the small flap, avoiding the punched hole. Multipurpose glue is great for this purpose as you’ll be able to reposition your DSP to get it lined up beautifully.

Once your DSP is attached, it’s very easy to see where you need to punch the label shape.

Do the same thing on the large flap.

And line up your Classic Label punch where needed.

Now your card looks like this!

Time to create the locking mechanism. For this, you will need a 2-1/4” circle punch or other die-cut shape that is wider than the hole. Using this punch (or die), cut a shape from the same colour cardstock as your cardbase. This circle will go inside your card.

Cut another circle – I happened to use the same colour, but you could use any colour you like – and decorate it as desired. This one will go on the outside of your card.

Position your inner circle and hold it in place with a Post-it note. Remember, you want the circle to cover the punched label slot.

Now, from the outside of the card, apply two Dimensionals. Notice that they are lined up with straight edges parallel to the edges of the punched-out label slot.

Remove the backing and mount the outer circle on the Dimensionals.

On the inside of the card, remove the Post-it note so that your inner circle can slide. (The inner and outer circle are now attached by the Dimensionals.)

The circles create a locking mechanism that slides across the label slot so that you can lock and unlock your card!

Decorate front and inside of card as desired.

Now remember – if you don’t already have the Classic Label punch (or any of the circle punches), get them right away as they are on the retirement list! Don’t miss out on these craftroom staples!

Happy Stampin’!

If you’re excited about the annual catalogue (and why wouldn’t you be?!), plan to join me at my virtual launch party on Thursday evening, May 6th! There will be games, prizes, product demonstrations, crafting, and lots of fun – and it’s ALL free! If you’d like a supply kit to craft along with me, please be sure to RSVP by April 29th so I can get it to you in time for the party!

Find all of the details here!

Product List

Thanks for reading today! If you enjoyed this post or found it useful, please consider sharing it! And be sure to join me on Facebook for daily content!

2 Responses to "Tutorial: Angled Slide-Lock Card"

Great tutorial (I am a visual person so this is awesome!) for such a fun card. Thank you for sharing. I made one this week and love it!

That’s so great, Louise! I’m so glad you enjoyed the tutorial and that it inspired you to get crafty! xo

Leave a Reply....

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s

Archives

Categories

I am an independent Stampin’ Up! demonstrator in Nanaimo, BC. I love creating cards and other handmade projects, and I love showing others how they can make their own creations! I hope you can find creative inspiration through my blog and my classes. Thanks for stopping by!

Join my In Color Club!

Join my Next Virtual Class!

Join my Paper Share!

JEB9Q4NS

Posts You Might Like:

Tutorial: Desk Organizer
Video Tutorial: Simple DSP Layout
Tutorial: Bay Window Card
Video Tutorial: Triple Accordion Card
Welcome to Inkyfingers Papercrafting
Virtual Events
%d bloggers like this: